--- title: "L-IFFT® (Live Inverse Fast Fourier Transform)" slug: "l-ifft-live-inverse-fast-fourier-transform" status: "update" updated: 2026-10-28T20:45:56Z published: 2026-10-28T20:45:56Z canonical: "doc360.rationalacoustics.com/l-ifft-live-inverse-fast-fourier-transform" --- > ## Documentation Index > Fetch the complete documentation index at: https://doc360.rationalacoustics.com/llms.txt > Use this file to discover all available pages before exploring further. # L-IFFT® (Live Inverse Fast Fourier Transform) [Embedded content](https://www.youtube.com/embed/Bge-uXnlYH8) --- *Live Inverse Fast Fourier Transform* (L-IFFT®) is an alternate view of the [Live IR plot](/v1/docs/live-ir) that uses the single time record FFT calculated with every Transfer Function measurement to plot an absolute time referenced live Impulse Response with the benefits of a real time transfer function measurement applied to it - specifically averaging and Magnitude thresholding. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(623).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A17Z&se=2026-11-18T18%3A30%3A17Z&sr=b&sp=r&sig=rxxOhK6lZBa8ojld3AR5JemD%2BpI1W%2FZ8OWPx1a0jJvY%3D) Each TF measurement in Smaart is simultaneously calculating an MTW, 32k FFT (by default, other sizes are selectable), and the polar and complex magnitude averaging of each. L-IFFT® takes the single time record complex FFT data and applies an IFFT to get the L-IFFT view. Older data can also be displayed in the L-IFFT® plot only if it was calculated using a single FFT (no MTW data). If the measurement at the top of the Z-order only has MTW data available, the L-IFFT selection is disabled, and nothing will appear in the plot. ## Accessing L-IFFT® L-IFFT® is only available in Smaart Suite and RT. It is accessed by navigating to [*Preferences* > *Advanced* > *Transfer Function Settings*](/v1/docs/advanced-preferences) and checking the box labeled *L-IFFTTM.* ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(619).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A17Z&se=2026-11-18T18%3A30%3A17Z&sr=b&sp=r&sig=YNGKid28L5DCOpYvSChcfFrlWvjtS5dghrW4%2F8jQ3FQ%3D) Once enabled, a secondary drop down in the Live IR graph allows you to select between Live IR and L-IFFT. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(620).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A17Z&se=2026-11-18T18%3A30%3A17Z&sr=b&sp=r&sig=iIAGmoBhcI4NWRJXmSERErqLDQL4NU4MarKzhgkxl7E%3D) Both views offer the standard Lin/Log/ETC graph types. --- ## Bandpass Filter The same octave bandpass filter used in the [Advanced Delay Finder](/v1/docs/delay-compensation#the-advanced-delay-finder) can be applied to the L-IFFT data using the in-plot widget (on the right side of the plot) to both enter the desired filter center frequency and then toggle it on/off via the checkbox. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(624).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A17Z&se=2026-11-18T18%3A30%3A17Z&sr=b&sp=r&sig=S2IgAYE7CtbxWlqstLhUSY4WW6uuo8n5SMUXOf69SSE%3D) This can be helpful when trying to view the Live IR of a low-frequency driver such as a subwoofer, which normally wouldn’t be visible using the Live IR. When doing this, it can also be helpful to switch to ETC view or use a larger FFT size, the latter of which can be set from within [*Transfer Function Measurement Settings*](/v1/docs/measurement-config-1#transfer-function-measurement-settings). While it may take longer for the Delay Finder to lock onto a delay time using a larger FFT size, a benefit of doing this is that it allows more time for lower frequencies to resolve. Performance can further be improved by using [a SyncSource measurement](/v1/docs/synchronous-source-syncsource-measurements) Signal. The frequency (magnitude and phase) response of a system, function or network. The transfer function of the linear time invariant (LTI) system can be measured directly, using techniques such as dual-FFT transfer function measurements that compare the output of the system to its input signal in the frequency domain, or by taking the Fourier transform of the system’s impulse response. The signal that describes the response of a system to an ideal impulsive stimulus in the time domain. The impulse response of linear time invariant (LTI) system is the inverse Fourier transform of its frequency-domain transfer function. 1. A number assigned to a quantity so that it may be compared with other quantities. 2. The absolute value of amplitude. As a convention, we most often use the terms amplitude to refer to linearly scaled quantities and magnitude when discussing amplitudes cast in logarithmic units such as decibels or orders of magnitude. Strictly speaking a signal can be any set of values that depends on some other set of values. In signal processing, the independent variable, e.g., time or frequency, is said to be the domain of the signal. In audio and acoustics, the things we most commonly think of as signals are time domain signals, where voltages or numeric values representing amplitude (the dependent variable) vary over time (the independent variable). But by strict definition, most of the things we see in Smaart could also be called signals, including transfer function Magnitude and Phase and RTA displays where relative energy or phase shift are presented as a function of frequency, rather than time.