--- title: "Trace Management (Smaart RTA Pro)" slug: "trace-management-smaart-rta-pro" updated: 2026-08-20T20:52:49Z published: 2026-08-20T20:52:49Z canonical: "doc360.rationalacoustics.com/trace-management-smaart-rta-pro" --- > ## Documentation Index > Fetch the complete documentation index at: https://doc360.rationalacoustics.com/llms.txt > Use this file to discover all available pages before exploring further. # Trace Management (Smaart RTA Pro) **Smaart RTA Pro** is capable of **capturing** and **averaging** RTA data - this allows you to take a snapshot (or picture) of the RTA response at that point in time. This capture can then be reviewed later or even sent to another person. Beyond that, you can capture multiple RTA responses and then average them together to create a spatially averaged response. --- **Capturing RTA Data:** Select the Camera icon in the upper-left corner of the RTA graph. You will be prompted to name the measurement, and it will be shown automatically until you hide it in the data folder. **Show/Hide is Select/Deselect:** Data focus in Smaart RTA Pro is tied to the Show/Hide state for that data. If a data trace is shown, it is also selected and ready to be averaged or deleted. **Averaging Stored Data:** To average two or more stored data traces, first turn on their display. Then, press the "Average" button. Whichever traces are shown will be averaged together. **Deleting Stored Data:** To delete stored data traces, select the traces you wish to delete by displaying them, and then select the Delete button. You can also manage your stored data traces directly from the file management system on your device. **Renaming Stored Data:** Simply long-press on the trace you wish to rename and you will be prompted to type a new name for it. --- ## dB vs Power Averaging **Power** and **Decibel (dB) averaging** refer to what type of data goes into resulting average. **Decibel averaging**, sometimes called arithmetic averaging, is a simple average of decibel magnitudes at each frequency. **Spatial power averaging**, on the other hand, is the average of squared linear magnitudes at each frequency with the result converted to decibels. Each has its own strengths and potential weaknesses to keep in mind. **Power averaging** is the typical (and often required) choice for applications such as background noise surveys or evaluating the average power Spectrum of sound across a wide area for any other reason. It tends to give more weight to the loudest sounds and, when used for single-channel Signal analysis where the focus is more on the sound being analyzed than the response of a system reproducing the sound, it can produce a result that best “looks how it sounds.” **Decibel averaging** produces an averaged result where all magnitudes are equally weighted. You might say that it tends to give more of a “consensus” view for all measurement positions than power averaging. When evaluating sound system frequency response, power averaging works best if all measurements being averaged are approximately equal in level. The decibel, often abbreviated as dB, is a logarithmic ratio between two values. In electronics and acoustics, decibels most commonly refer to the ratio between a given amplitude value and the number 1, where some reference value such as the maximum output of an A/D converter (dB Full Scale or dBFS) or the threshold of audibility for human hearing (for dB SPL) is scaled to equal 1. The decibel value for an amplitude is then calculated as: dB = 20·Log10(A) = 10·Log10(A 2 ), where A is linear amplitude. In this case, amplitude values greater than one yield positive decibel values and numbers smaller than one become negative dB values. This is why dB FS values are most often negative and dB values in sound level measurements are nearly always positive. The frequency content of a given signal. Strictly speaking a signal can be any set of values that depends on some other set of values. In signal processing, the independent variable, e.g., time or frequency, is said to be the domain of the signal. In audio and acoustics, the things we most commonly think of as signals are time domain signals, where voltages or numeric values representing amplitude (the dependent variable) vary over time (the independent variable). But by strict definition, most of the things we see in Smaart could also be called signals, including transfer function Magnitude and Phase and RTA displays where relative energy or phase shift are presented as a function of frequency, rather than time.