--- title: "Feedback/Input Signal Coming From Outputs" slug: "feedback-input-signal-coming-from-outputs" updated: 2026-09-04T18:21:15Z published: 2026-09-04T18:21:15Z canonical: "doc360.rationalacoustics.com/feedback-input-signal-coming-from-outputs" --- > ## Documentation Index > Fetch the complete documentation index at: https://doc360.rationalacoustics.com/llms.txt > Use this file to discover all available pages before exploring further. # Feedback/Input Signal Coming From Outputs If you're receiving feedback from your IO device’s output(s), or if the input Signal is playing through them, this may be caused by a mixer control either on the physical interface itself or within its control application. Some audio interfaces may have an "input/playback" mixing knob that will switch between which signals are being sent to the outputs. This is most commonly used in a recording environment for monitoring an instrument being tracked. When performing acoustical analysis, we do not want the input signal to play back through the outputs as this can cause feedback. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(406).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A15Z&se=2026-11-18T18%3A30%3A15Z&sr=b&sp=r&sig=cjNiZce8jbS8ELfEHTkqkescB8GYEBDp5SWidbySHXo%3D) *On Avid's MBox Mini, the "Mix" knob controls whether the input or output signal is sent to the output channels. For use within Smaart, turn the knob all the way to the right towards “P/B”.* In most cases, the audio interface should be set to "playback" mode. Other interfaces may use the term "direct monitor" (i.e. directly monitoring the input signal), which should similarly be disabled or toggled off. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(407).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A15Z&se=2026-11-18T18%3A30%3A15Z&sr=b&sp=r&sig=UnEkkD9gsvWsh1QY3iJbqcz8G0NKjHH6p%2FOFwcRb%2B3Y%3D) *When using the Focusrite Scarlett 2i2 (Gen2) with Smaart, ensure the "Direct Monitor" switch is in the “OFF” position.* Lastly, some interfaces come with a built-in mixer or other control software, which can be used to route signals between different sources. The Roland Octa-Capture is a common example. ![](https://cdn.document360.io/a725c8f7-3a1a-4c09-9518-5d15d09a2ae2/Images/Documentation/image(408).png?sv=2026-02-06&spr=https&st=2026-11-18T17%3A30%3A15Z&se=2026-11-18T18%3A30%3A15Z&sr=b&sp=r&sig=RpI1OF0D9q2tSq8F29s2uiws%2Fp%2F%2FABssP%2FoDSjD%2Bdiw%3D) After opening the Octa-Capture Control Panel, select the button to the upper-right to switch from preamp control to the Direct Mixer. In the master output section to the right, ensure that the *Input Mixer* master fader is set to *-INF*. This can be performed through the display on the front panel of the unit itself, though it's typically easier to manage it through the Control App. If issues persist, or if you're having trouble finding where to change this setting on your interface, [please submit a ticket](https://www.rationalacoustics.com/support-ticket) or send an email to [support@rationalacoustics.com](mailto:support@rationalacoustics.com). Strictly speaking a signal can be any set of values that depends on some other set of values. In signal processing, the independent variable, e.g., time or frequency, is said to be the domain of the signal. In audio and acoustics, the things we most commonly think of as signals are time domain signals, where voltages or numeric values representing amplitude (the dependent variable) vary over time (the independent variable). But by strict definition, most of the things we see in Smaart could also be called signals, including transfer function Magnitude and Phase and RTA displays where relative energy or phase shift are presented as a function of frequency, rather than time.